• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your first line of defense against unauthorized access to your home. Locks might require replacement because of signs of wear and tear, or other situations such as moving into a new home or a burglary.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the right-sized lock.

Deadbolt

If you want to ensure your door is safe from burglars, it's a good idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder through the door. A single-cylinder deadbolt can be activated by a key located on the exterior and a thumb-turn piece situated inside. Deadbolts will only work when it is properly installed.

You will first need to determine if the door has an existing hole for a deadbolt, or if you need to bore it out. With the template included with the lock installation kit, mark the location of the hole for the deadbolt on the door's surface. Use your tape measure to determine the height of the deadbolt. Then, mark this height on the side of the door. You can then use a speed square to draw straight lines across the mark you made for Replace Door Lock the bolt hole.

Then by using a power drill, bore through the hole until it reaches the opposite side of the door. This could take a bit of time. Then, sand the hole and the edge of the door so that it is smooth. At this point, it's a good idea to paint or stain your door.

Remove any screws that are visible from the deadbolt. This will reveal both the front and rear assemblies of the deadbolt, as well as its bolt inside. Then, remove the bolt and Replace door lock it by an alternative bolt that matches your door hardware. You will need to unscrew the bolt from the setplate. Then, you'll need to chisel the door frame for the strike plate.

If your strike plate is out of alignment it could be because the previous installer failed to mortise it correctly or an installation of a weatherstripping altered the strike position. To fix this issue, you will need to remortise the strike plate as well as the deadbolt. Close and lock the deadbolt when you've completed this process. Make sure that the bolt extends into the strike plate and then test the key to ensure it is able to open and close smoothly.

Knob

When a door knob is worn out it could make your home or business less secure. It could make opening or closing the door more difficult, which is why it is an ideal idea to replace the knob. replacing a patio door lock knobs is an easy DIY project and Replace Door Lock shouldn't take less than 30 minutes to complete. Make use of pliers or a screwdriver to remove any knobs or handles. Be careful not to damage other parts of the door.

Before you begin you'll need to spray WD-40 or some other dry lubricant onto the mechanism of the knob for your door. This will help the new lock move smoothly when you turn it. To ensure that it operates properly it is essential to select the right knob and handle to match your existing doors. If you don't already have a matching doorknob and handle, you'll need to buy a replacement.

To begin the replacement door lock process, look at the knob or handle to see the screws that hold it in place. If there aren't any screws, you can use a screwdriver to insert between the cover plate and the hidden screws plate and then remove it.

After taking the knob off examine it for signs of rust and damage. If the knob has any scratches or marks it's time clean it. Otherwise it shouldn't need any major work.

Now it's time to install the new one. First, examine the two new knobs to ensure you're picking out the right one for your door. You'll want to pick one with an extending rod that's designed to lock into the second knob's rod mechanism. Once you've positioned the new knob in the door's hole, carefully insert it into the latch.

Thread the latch plate screws down, then test the spring by pressing down repeatedly. The latch should spring back up every time. Install the second knob and secure it to the rod mechanism of the first knob. Then, thread the other long screws from the knob's interior through the hole for the cylinder on the exterior doorknob and lock it in place.

Latch

A latch is a piece metal that extends through the door jamb to keep it closed. It is operated with a knob or handle on the inside of the door or a thumb turn on the outside side of the door. A deadbolt is a device used to secure a latch and stop intrusions from breaking through the glass of the door. It can also protect against intentional or accidental closing by pets or children. A latch can be set with single cylinder deadbolts or double glazed door lock replacement cylinder deadbolts, depending on the security level you prefer.

Installing a latch involves the same steps similar to installing a deadbolt however there are some differences. To ensure that the new lock will work first, take a measurement of the setback on the doorjamb using an instrument such as a tape measure. The setback is measured from the edge of the doorjamb up to the middle of the hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is larger than that, you might need to purchase a latch that is larger from a hardware or locksmith store.

The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Utilize a chisel to smooth out the mortise of the latch, making sure it's deep enough to allow the faceplate of the new latch to be flush with the doorjamb. Place the strike plate in place to ensure that it is positioned correctly.

If the strike is placed too high, the door can be pushed into or pressure applied to it with a crowbar or tire iron. This could cause the doorjamb's to crack. This can be fixed by drilling a new hole through the doorjamb, and chiseling the core out of the hole that was previously made.

The final step is to install the new strike plate which can be accomplished by screwing it over the screw holes that are already in place. Use wood putty afterwards to fill in any existing bolt holes or screw holes that aren't being used. When the putty is dry, sand it smooth for an elegant finish.

Strike

An electric strike is the metal piece that holds the deadbolt and latch are engaged when the door is shut. It is an essential component of the lock's overall security because it stops the door from opening, and also provides additional resistance to force or kicking. If a door has been equipped with an electric strike, it will only be opened using keys or the control unit that governs the electrical impulses.

In the past, installing an electronic strike required cutting a portion of a doorjamb to let the latchbolt of a cylindrical lock from the pocket within the strike. This is an inconvenience when it comes to the aesthetics of an opening as well as exposing the latchbolt and keeper mechanism to any unauthorised users.

Recently, several electric strike manufacturers have developed an innovative type of electric strike called the "No Cut" strike that doesn't need a cutout in the doorjamb for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the keeper and latchbolt when it receives an electrical impulse from a reader or controller. The retracting of the keeper as well as latchbolt raises them on the ramp, locking the door. When the door is closed the deadbolt remains in place and the latchbolt retracts in the keeper.

Installing an electric strike is an easy process, particularly in the case of replacing a upvc door lock a strike on an existing door. If, however, you are upgrading to an electric strike for an access control system, you will have to ensure that your new system is compatible with the type of lock you've chosen to install. Also, you must ensure that the strike is connected to your access-control system and is configured to function in a fail-safe way.

One way to protect against access by unauthorized persons is to upgrade the strike on your doors to a high-quality strike plate. These plates are fitted with four to six three-inch screws instead of the two, three-fourth inch screws that are typically employed in regular strikes. These longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt cylinder more difficult.