• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

It can be difficult to install the flap for your cat, but with the right instructions, it's not too difficult. Firstly, determine how high you want the flap to be (on average, belly height). Note this on the door and use the template as a reference to drill.

If you have a young kitten you can prop the door open very slightly and gradually allow it to go through. Reward it as it passes through wall cat flap.

Take a measurement of the door

A cat flap is a wonderful way to let your pet move in and out of your home as it likes. This can keep your cat healthy as it ensures that it is exercising regularly and be able to go back inside when it is stranded outside in bad weather. This will reduce the amount of time you allow your cat go in and out and make your home secure by letting you know when it's left.

It is important to ensure that the cat flap is placed correctly to stop your pet from being forced through through it by other animals (e.g. dogs). It is essential to measure your pet's belly height and the entrance to your home to make sure that the flap is at the correct height. You can alter the height of your flap in case your cat is smaller or taller than average.

Next, use a spirit-level to mark the center of the door. This is where you will install the flap. Then, using the mark as a guideline, cut out the form of your flap using a jigsaw. After cutting the area out then sand the edges to create smooth surfaces. Drill any necessary holes.

Fitting a cat flap should not take longer than two hours. However, the process may be slightly more complicated if you need to fit it onto a uPVC or composite door because these doors come in a wide range of thicknesses which can affect how the holes are cut and the type of door they are fixed to. This is why we recommend calling a professional to complete the work, particularly in the event that you've never worked with glass cat flap installation near me before.

Measure Your Cat

You will not have to spend hours of ignoring the pet meow to be allowed in or out. This is particularly helpful when your cat is inside during the winter months when you are at work.

It is essential to measure your cat first before attempting to install. It might seem like a straightforward task, but it's essential to get the measurements right. Otherwise, your pet may have difficulty putting it in use.

First, make sure your cat is calm before taking measurements. You'll need to hold them in a position where they are not able to move, and ensure that the ruler or measuring tape is flat against their body, not bending in any place. You can take a precise measurement by keeping the measuring tape or the ruler flat against the body of the animal from the top to the bottom.

Once you've got the measurement of your cat's body, it's time to look at the door and decide where to put the flap. A good tip is to place the flap in the middle of your cat's belly because it will allow them to pass through it without too much effort. This will also stop the flap from making lots of noise when it opens and closes.

You should consider the thickness of the uPVC or composite door too. While all doors made of timber have a similar thickness to them, cat flaps uPVC or composite doors can differ greatly in their overall structure. This could make the process of the installation of the flap for your cat more difficult since you have to make sure that the hole is the right size.

You can make use of the template included in the instructions to mark the location of the hole on the door. This will allow you determine where the opening must be, and also to make sure that the template is placed correctly on the door. Utilizing a spirit level to make sure that the template is flush against the door will also be very helpful.

Cut the Flap

Before you can put in your cat flap, you'll must cut the door panel to make a space big enough for it. This can be a daunting task and it is recommended that you get a professional assist you if you don't have the knowledge or skills. It is also recommended to read the instructions included with the cat flap kit to discover how to do it correctly.

To do this you need to determine the height of your cat's or kitten's belly. Use this as an indication point. A good rule of thumb is to place the flap of your cat about 10 centimeters off the ground, as this is approximately the average height of the cat's belly. This will allow your cat to move through the flap easily and make it more difficult for other cats or naughty neighbours to enter or exit.

Once you've decided the location where the cat flap needs to be located, mark the location on the door using a pencil. If your kit comes with a paper template, lay it on top of the door and use the markings to drill holes in each corner of the template. You should then be able to cut the shape of the template and replace it with your cat flap.

If you are installing your cat flap in an entryway made of wood or uPVC, it is possible to do it yourself if you feel confident enough to handle a Jigsaw. Be careful not to cut into the mullions or rails that run vertically of your door. You can use a jigsaw cut the panel into a circle or square according to the design of your cat flap. Take your time and don't make the jigsaw cut faster.

After the hole has been cut and the flap is firmly positioned, carefully place the flap onto its new location and make sure that it is firmly secured. If the flap is fitted with screw caps put them on the protruding bolts. Once the screws are in place, sand the rough edges of the cut then apply sealant to any gaps to ensure there aren't any draughts getting into your home.

Fit the Flap

If you have a standard cat flap, you can help your pet through it by placing a small amount of cat flap installers food on the front of the door. Alternately, you can push the cat through using your hands or with a stick. Once your cat is used to walking through the flap, it is likely to be able in and out as it pleases and you should be able to let it out or in without having to be there keeping the door open for it all day (and potentially in all weather conditions).

You can fit an animal flap inside the UPVC or glass doors but it's not quite as straightforward as fitting one into a timber exterior door due to the fact that the UPVC doors and some glass doors aren't a uniform thickness. This could have a significant impact on how you cut the hole for the flap and could affect the way your flap is fitted correctly after it has been installed.

Based on the type of cat flap you pick, it may include a mounting kit and a template that will show precisely where to drill holes for it. If the kit doesn't come with the template you can use a photocopier to make your own. It's important not to press the jigsaw too hard when cutting, so that it doesn't create a larger than necessary hole in your door.

The majority of cat flaps are square or rectangular in shape, however there are also some which are circular, and are generally more difficult to fit. If you have a circular flap, it's essential to make sure the hole is in the right position on your door because if it's not, the cat can't use it and could be left out in the sun all day (or even at night).

Certain models of cat flaps come with locks that allow you to regulate when your cat comes and goes. These are very helpful when you're concerned about your cat going out at night and coming back door with cat flap fitted in because of the darkness, or you're working all day. Certain locks can be used to lock access or exit, and others can be locked both ways. This is useful for older cats or sick cats who aren't keen to go outside in bad weather.