• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and boarding up windows Doors Before a Storm Hits

In the event of a storm, boarding up your windows and doors provides measurable protection from damage. You'll require some items to accomplish this.

First, take measurements of the window's width and height including the framing (not the trim around it or masonry). Keep these measurements in mind so you won't forget.

Preparation

It is recommended to board up doors and windows before an event like a storm or natural disaster hits. This will reduce property damage and reduce the chance of dying. Boarding up windows requires lots of preparation, like purchasing and measuring plywood boards and identifying the exact size of each window to be covered. It also takes time to cut the boards and put them up them correctly. It is possible to speed up the process by starting the preparations immediately you hear of a storm approaching your area. You will avoid having to rush in the last minute and make it simpler for you and your employees.

Start by listening to the forecasters for weather and follow the guidelines laid out by your local government. If you start earlier in the process, you'll be able to gather the materials and store them without being overwhelmed by the approaching storm. Depending on the severity of the pending event, you may need huge quantities of plywood to cover your windows. Make use of a tape to determine the width and height of each window opening. Make sure to include the framing or trim around each window, as well as any ledges with extended edges if they are necessary.

Divide the total width and the height of your window by two to determine the number of plywood sheets you'll need. For instance, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If your exterior boarding up Windows is made of wood, make pilot holes into the plywood sheet to align with the window frame below. This will reduce splitting when you screw in the screws.

To make sure that the window's opening is bigger than what a sheet of plywood can accommodate cut two sheets that are each half the size of the desired window and lay them side-by-side on the wall. Then cut a piece of 2 by 4 inches (5.1 by 10.2 cm) lumber to the length of the connecting edges of the sheets of plywood and lay it over the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet and through the bracing to join the two.

Materials

To ensure safety and security ensure safety and security, use only materials that are sturdy and won't break or splinter in strong winds. Plywood is a popular material for boarding up windows. It is simple to use, affordable, and readily available. Select plywood that is exterior grade (CDX) since it is stronger and will contain fewer warps and knots. A stronger option is storm shutters or hurricane shutters, which are put up over windows that are already in place to provide more protection against glass shattering and the weather that can cause a lot of damage.

Once you've identified the position of your window openings take measurements of the height and width of each to determine how much plywood you will need. Use a power drill to drill pilot holes into the plywood sheets around the windows at intervals of two inches. Mark the studs on the wall before attaching the plywood to ensure the boards are securely fastened. If your home has wood siding, search for nailheads that may indicate stud locations. You can also use a drill to locate the stud locations. Be sure to insert the screws into the framing, not the trim or sheathing; a plywood panel attached only to these materials could become dangerous in winds that are strong.

If your window is too big for one sheet of plywood, you could cut two pieces of plywood that are half of the size needed and join them using two by four inches of lumber. Label each plywood piece to let you know what window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing as well as the studs to attach the plywood panels to your wall. Make sure to insert the screws into the studs so that they are about half as deep as the thickness of the plywood, however, be cautious not to go too deep and cause damage to the structure of your house.

You should also think about installing polycarbonate security glass such as DefenseLite on your primary windows. These transparent shields are secured to the existing glass and safeguard your doors and windows. They are virtually indestructible and deter criminals from gaining entry into your home.

Installation

If you live in or are planning to move to a place susceptible to hurricanes and are worried about the storm it is recommended to board up all your doors and windows. This task can be completed quickly and efficiently, but only if the boards are cut, measured, and labeled before the storm arrives.

You'll also require other tools, such as a drill (or nails and a hammer for those who don't own an electric drill), tape, a saw gloves, a level and safety glasses. It's a good idea apply sealant to the plywood, as well, to make it waterproof.

Begin by measuring the window's height and width. Then cut the plywood sheets to fit within the frames. It is recommended to cut the sheets on-site, as it allows you to control the precise dimensions of the plywood.

Cut the boards to the size you want with a track or circular saw. Once installed it is necessary to sand down all of them. Once you've put your boards in place, screw three-inch stainless steel hanger bolts into the framing studs of each window. Use washers on each bolt and wings nuts to ensure they are secured. Make sure that each screw penetrates at least 2 inches deep into the studs to ensure that the boarding up services is sturdy enough to withstand strong winds.

If you're building with concrete block, you could attach the plywood to the building using galvanized pan-head screws driven through the edges that overlap of each panel into bricks or cinder blocks. It is also necessary to drill pilots into the masonry before screwing corrosion-resistant screws into the holes. It's a project that could take as long as three hours per window, so it's essential to begin the process immediately after you hear that a hurricane warning has been issued. This will give you ample time to finish the project before the storm strikes.

Maintenance

You should be prepared to secure your doors and windows prior to an extreme storm. This will save you from costly repairs and shield your home from further damage caused by rain, wind debris, flying debris and other factors that can affect windows.

The right materials will make boarding up doorway up simpler and faster. It is crucial to accurately measure every window. This will ensure that the OSB or plywood fits snugly, and that it will not be able to slide off easily. If you're using plywood make sure you use exterior grade sheets, and consider adding an extra layer of protection.

Mark the places where the screws are going to be put into the board after you have taken measurements of the OSB or plywood. Utilize a drill to predrill holes at intervals of 12 inches into the plywood. You can then use hanger bolts to secure the boards in a emergency boarding up services situation. Once the storm has passed and you've received the all-clear by local authorities, remove the hanger bolts, but keep them in place for future emergency situations.

Next, install the plywood panels over the windows. Be prepared to work in pairs. If you're using plywood, ensure that you sand the edges to ensure they're smooth and won't scratch paint or trim. Then, attach the frame to the plywood with corrosion-resistant screws that fit into the pilot holes. If your home has shingles made of vinyl it, attach the plywood directly to the shingles, and not to the wood framing.

A window that is boarded up can be used to discourage burglars. Burglars are more likely attack a building that has a damaged or unlocked window. Also, they are more likely to break into the store with a boarded up window than one that has no. This is something that retail business owners should take very seriously.