• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace a lock on a upvc door to replace Door lock Door Locks

Door locks are the first security measure against unauthorized entry into your home. Signs of wear and tear, and also instances like moving into a new house or burglaries, may trigger the necessity of replacing upvc door lock your lock.

To begin, determine the size of your cylinder using the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will assist you select the appropriate lock.

Deadbolt

If you want to make sure your door is secure from intruders, it's a good idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder through the door. A single-cylinder deadbolt can be activated by a key located on the exterior and a thumb-turn piece situated inside. Deadbolts can only function if it is installed correctly.

First, you will need to determine if the door has a hole for a deadbolt or if it needs to be bored out. With the template included with the lock installation kit mark the spot of the deadbolt's hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Mark this high point on the door's edge and use the speedsquare to draw a straight line across the mark you made for the bolthole.

Then by using a power drill, bore out the hole until it reaches the opposite side of the door. This may take a while. Then, sand the hole and the edge of the door until it's smooth. At this stage, it's a great idea to paint or stain your door.

Remove any screws that are visible from the deadbolt. This will reveal the front and back assemblies of the deadbolt and also the bolt that is inside. Then, loosen the bolt and replace it with a new one that matches the door hardware. You'll need to remove the bolt from the setplate. After that it is time to chisel the area for the strike plate that is on the door frame.

If your strike plate is not aligned It's likely that the previous installer didn't mortise it correctly or a weatherstripping was installed and changed the strike position. You will need to re-mortise the strikeplate and possibly even the deadbolt itself to fix this issue. Close and lock the deadbolt when you've completed this process. Be sure the bolt is extending into the strike plate then test the key to ensure it opens and closes smoothly.

Knob

If the knob on your door is damaged, it can make your home or business less secure. It may also make it harder to open or close the door, so it's a good idea to replace it. replacing a upvc door lock the knob is an simple DIY project that shouldn't take less than 30 minutes to complete. You can use a screwdriver as well as pliers to take off the old knob or handle Be careful not to harm any other parts on the door.

Before starting, you'll want to spray WD-40 or some other dry lubricant on the mechanism of the knob for your door. This will help the new lock slide smoothly as you turn it. To ensure proper operation, it's important to choose the right knob and handle to match the doors you already have. If you don't already have a doorknob that matches, you will need to purchase a new one.

To begin the replacement process, first look over the knob or handle to determine what screws hold it in place. If there aren't any screws you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and pop it off.

Once you've removed the old knob, examine it for any indications of damage or rust. If the knob shows any dents or marks it's time clean it. Otherwise it shouldn't require any major work.

Now is the time to put in the new one. It is important to first look over the two knobs in order to make sure that you are choosing the right one for the door. You'll need to select one with an extended rod that locks with the rod mechanism of the other knob. Once you've put the new knob into the hole, slide it into the latch.

Test the spring by pressing it down repeatedly. The latch should then spring back up every time. Install the second knob and secure it to the rod mechanism of the first knob. Then, thread the other long screws from the interior knob through the cylinder hole on the doorknob on the outside and secure it.

Latch

A latch is a steel piece that extends into the doorjamb to keep it closed. It is operated by a handle or knob on the interior side of the door, or a thumb turn on the exterior side of the door. The latch can be secured using deadbolts to prevent intrusions from piercing the glass. It can also guard against accidental or Replace door Lock intentional closing by pets or children. You can choose to install an entry point with either a single-cylinder or double-cylinder deadbolt based on your preferred level of security.

Installing a deadbolt is the same as installing a latch but there are some differences. To make sure that the new lock is compatible first, measure the setback on the doorjamb using an instrument such as a tape measure. The setback is measured from the edge of the doorjamb all the way to the center of hole for the latch plate. A standard setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you might need to purchase a larger latch from a hardware shop or locksmith.

Next, drill a hole for the latch plate at the edge of the doorjamb. Utilize a chisel to smooth out the latch mortise, making sure it's deep enough for the faceplate of the new latch to be flush with the doorjamb. Tape the strikeplate to the doorjamb to ensure it's placed correctly.

If the strike is placed too high, the door could be pushed in or pressure applied to it using a crowbar, or tire iron. This can also crack the doorjamb. To correct this, the strike could be lowered by drilling a new hole into the doorjamb and chiseling out the core of the old hole.

Installing the new strike plate is the last step. This can be done by screwing the new plate into the screw holes that are already in place. Utilize wood putty to fill in any existing holes for screws or bolts that won't be used. Once the putty is dry you can sand it down to give it a professional results.

Strike

An electric strike is the metallic part where the deadbolt and latch engage when the door is closed. It is a crucial component of a lock's overall security, since it keeps the door shut and provides extra resistance to force or kicking applied to the door. If a door comes with an electronic strike, it can be opened only by keys and the control unit that controls its electrical impulses.

Traditionally, installing an electric strike involved cutting out a portion of the doorjamb in order to release the latchbolt of a circular lock from the pocket of the strike. This is not only unattractive and unattractive, but also exposes the latchbolt mechanism and keeper to uninitiated users.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that doesn't require a cutout for operation. These strikes utilize a special design that allows the keeper and latchbolt to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp which lifts the latchbolt and keeper when it receives a signal from the reader. The keeper and latchbolt are pushed up the ramp by the retraction. When the door is closed the deadbolt remains in retracted and the latchbolt retracts into the keeper.

Installing an electronic strike is a simple procedure, particularly in the case of replacing a upvc door lock an existing strike. If you're planning to upgrade an access control system to an electric strike, it is important to make sure that the new system is compatible. You will also have to make sure that the strike is properly connected to your access control system and is set up to function in a safe manner.

Upgrade your strike plates with heavy duty strike plates to stop the entry of unauthorized persons. These plates use four to six screws of three inches instead of the two, three-fourth inch screws typically used in regular strikes. These longer screws make it harder for anyone to break the frame and reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.