• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix Car Ignition Problems

The car will not start until the switch sends an electrical signal to the starter. Over time wear and tear may cause the switch to malfunction.

Utilizing specially designed tools, you can take off the trim on your steering column and access the ignition cylinder module. Check out your repair manual to learn how to do it correctly.

1. Make sure you check the Switch

A defective switch is among the most frequently encountered ignition issues. It functions as bridge between two contacts, regulating when relays activate and deactivate. It is less likely to fail because it does not channel the full power from devices like the starter. However, it's still possible for the switch to get damaged or corrosion-prone.

A defective switch can be identified by a difficult time turning the key. This could be due to many things, including improperly inserting the key, or deteriorating the mechanism over time. It's not unusual for people to confuse their keys with those of others. This can result in mechanical damage.

If the switch isn't working there are a few things you could try before calling a locksmith ignition replacement cost. First, you must ensure that the battery is fully charged and there aren't any electrical issues with the system. You should also check the voltage of each component to see if they're providing enough power. After you've completed these steps, you're ready to start troubleshooting.

The ignition switch is easy to replace. It is connected to the ignition module, which is a round piece of equipment that connects everything. To replace it, you'll require an flathead screwdriver as well as something that is long enough to push the pin into. It could be anything from a paintbrush handle to a kabob skewer, but you should stay clear of anything that is brittle and break within the hole.

Remove any trimming pieces that overhang the switch when you're ready to get started. After removing the trim pieces, take off any screws that hold the switch in place. Then, gently pull it out. Depending on the model you may have to cut off any cables that connect to it. Find out how to do it in the instruction manual for your vehicle.

It's best to get the ignition switch replaced by an expert when it's not working. The replacement process involves turning off the steering column, which could result in unintentional airbag deployment if it's done in a wrong manner. For this reason, it is recommended to let your locksmith take care of this for you.

2. Check the Wiring

Your car might not start if you cannot turn the key or it won't start. This could be due to any number of components within the ignition system. Understanding how the ignition system functions will help you determine the cause of the problem and make the appropriate repairs.

The ignition switch is a low voltage multi-pole electrical switch which is operated by a key. It has four positions including off run, accessory, and "lock." If the switch is in the lock position (which usually has an indicator in red), the ignition circuit is active and it's not possible to start the engine.

To determine if the ignition switch is damaged or if the ignition coil is faulty, you'll have to conduct an electrical test with the help of a voltmeter. The voltmeter should read around 12.6 volts when the ignition switch is in the running position. If the voltage is lower than that it indicates that there is an open circuit somewhere within the system. It could be the solenoid, the battery or the ignition coil.

Disconnect the electrical connector so that it doesn't interfere with the test. Set the voltmeter in the resistance or continuity modes and then place one lead on one of the terminals on the ignition switch. The other lead should be connected to the positive terminal of the battery. If the voltage meter shows "open" or doesn't register any voltage, it's time to replace the switch.

When you're replacing the switch, be sure to use a new mobile ignition lock repair services cylinder and a good quality key cut to ensure that your car will run and start correctly. When you replace the switch, ensure not to touch the pins of the cylinder's ignition with your tools. Otherwise, they'll get stuck and the engine won't be able to run. In some vehicles, you'll have to remove the steering column and the gear selector in order to access the ignition cylinder. This can be difficult, and it is not recommended until you have a vehicle's owner's guideline that states it's safe. Otherwise serious damage to the steering column or shifting mechanism is likely.

3. Check the Cylinder

If you've worked your way through the wiring, battery, and ignition switch and still can't get your car ignition switch repair to start, it could be time to examine the cylinder. It's the part that holds your key and is mechanically connected to the steering wheel lock so that a potential thief cannot control the car without keys.

You might notice that your key will not turn if the cylinder has worn out. Sometimes, the pins in the cylinder become stuck when they adjust to the shape of the key, which can cause your car not to start. The cylinder may also be sloppy. A tap using a small tackhammer will help. Just be careful not to crush the springs inside and ensure that your key is properly installed prior to tapping.

If you are required to jiggle and move your key before it will start, this is another sign that your cylinder has gone bad. This is a sign of trouble and must be addressed immediately, since it will only get worse with time.

To test the cylinder, you'll have to disconnect your battery, and then remove the cover around your steering wheel until you're able to access the ignition module. You'll then be able to pull out the old ignition switch as well as the cylinder for ignition made of metal. If you don't own an extra switch, you might be able take your original ignition cylinder as well as switch to locksmiths for reuse as long they're in good shape. After replacing the ignition switch and cylinder, ensure that you reconnect the wiring, secure it and reattach all covers and panels that you took off.

4. Check the Spark Plugs

The spark plug is the final link in your ignition chain. If it fails it will stop the engine from running. It can be that your car ignition switch repair will not start at all, or it will run poorly. In either case, it is likely that one or more things are preventing or impeding electrical current from crossing spark plug gaps, which in turn ignites the mixture of fuel and air within your engine.

Make sure you wear protective tools and gloves before you begin working with your spark plugs. Spark plugs can be hot and cause serious injuries if you touch them with your naked skin.

You might notice a light gray or brown fleck on the top of the electrode if the spark plug is damaged. It may also have a black layer on the side of the electrode. These deposits, also known as fouling, may prevent high-voltage electrical current from crossing the gap between the spark plug and sparking your engine.

If you suspect your spark plugs might be the culprit you can test them if you remove them from their tube inside the ignition coil. This can be accomplished by disconnecting the coil and the plug wire. Then, you'll be required to follow the correct procedure for your vehicle to take off the components that are covering the plugs. Once you have removed the plugs you can place them on a surface that is grounded and then crank the engine. If they're functioning you should see a bright blue spark near the point of the central electrode.

If you do not detect a spark, you've discovered the problem. The next step is to go through the fix ignition switch chain, testing each part until you find out what's stopping the spark plugs from performing their job. All systems get older and eventually break, and this is particularly applicable to ignition systems. Regular maintenance can reduce the wear and tear and prevent major problems at the worst time.